# How to Wire a Dual 2 ohm Subwoofer to a 4 ohm Final Impedance | Car Audio 101

Tags:1 ohm2 ohm2 ohm dvc2 ohm to 4 ohm4 ohmAmpamplifieraudiobasscarcar audiocar audio 101dualdual voice coilElectronicsfinal impedancehow do Ihow to wire dual 2 ohm to 4 ohmhow to wire subwooferimpedancelearnmobileohms lawPARALLELseriessinglesonicSonic ElectronixsoundsubSubwoofersubwoofer wiringsystemtutorialtwowire to ampwiring

first

do wire 3 DVC 4ohm subs please and thank you

into what final impedance ?

REQUEST: two dual 1ohm to .5 ohm. Please and thank you.

Thanks a lot!

ok thanks didnt know

i have SPL Z2X-1200 and TS-W126DVC and im trying to get the best conection can u help me please.

thankkk you

Excellent video, straight and to the point, thanks!

thanks, was looking for a solution with my 2ohm DVC sub to 4 ohm amp, all i find is crap, till i found this. thanks a lot.

thanks 🙂

Just bought a dual 2ohm 8" sundown woofer, this helped me!

How do you make a class ab Amplifier to do i ohm

By wiring the 2 ohm to a 4 ohm how is that helping. Also I'm looking at a 2 ohm (SPL FWX 154) (peak watt.2200/ RMS watt.1000) and I will be running that speaker off a 3500watt planet audio will this be a good setup. Any advice is good advice thank you.

I have two solo-baric s15l7 2 coil 2 ohms each how do i connected to a ZX450.2 kicker amp i have two of those amps best way to connect to have a good sound out off it any suggestions.

Can you wire a dual 2 ohm sub to a 2 ohm amp?

Could I do this with 2 subs and connect the positives and negatives and connect them to my amp bridged at 4 ohms?

if you wire a dual 2 ohm to a 4 ohm impedance, can you still push the same rms power that it was rated at @ 2 ohms?

I need some help I have two woofer the two of them is dual but here is way my problem comes I want to wire them together but on is a dual 2 ohms and the next one is a dual 4 ohms i like to wire them to 4 ohms final impedance can it be done I really need some help

What guage speaker wore should I be using if I'm only pushing 450 watts

You have nothing about 2 Dual 1 ohm….my question is can I make 2 dual 1 ohm come out to 1 ohm…

Need help. I have 4 type r 10" subs an 2 old skool punch 800a2. Im tryn to get 2 subs to 4ohms so i can bridge them. Is it possible

So..can i connect 2 channel

in 1 speaker?

I've got a mono amp and want to push a 4 ohm load. I am using only one sub. The sub is a dual voice coil, each voice coil is 2 ohms. The dilemma is that, even though it's a true mono amp, it has 2 positive speaker outputs and 2 negative speaker outputs … not left and right — but just like this:

+ + – -. How do I wire that single sub to those outputs, do I somehow use both positives and both negatives or what? I want to make sure that amp sees 4 ohm because my power and ground wires and fuse are not going to be able to handle 2 ohms. Anybody have a solution?

Please answer this damn question how do you wire a 2×2 ohm single subwoofer to 2 ohms? Jump the other side and then use the other side?

Need some help please. I've got two 12 inch crossfire DB3 Series DVC 2/8 ohm. So subs being 2/8 ohm how do I wire them both to 4 ohm's being 2/8 ohm's or are they the same as a regular 2 ohm sub. Thank you

I have a sub with a final impedance of 2 ohms but my amp is 4 ohms, how can I wire it?

Can wire it from just one side does it make 2ohm ?

Dual 2 ohm wired to 2 ohms? This is one sub.

Bout to get a 15" dual 2 ohn woofer, this shit is gonna explode my car

can you wire 2 x 2ohm dvc subs to get A 4ohm load to the amplifier

How do i keep a dual 4 ohm to 4 ohm

How many RMS have on 4 ohm when out 2 ohm have 1500 watt RMS ?

You cannot mess that ?

what would happen if you put power and ground separately and connected to 2 channels on a amp? have a friend who did that and it sound fine?

If you put two of those at a 4-ohm final what is going into the amp, 2 ohms ?

I did this with a 2ohm Kicker CompR and I'm getting a 5.5ohm reading. Anyone know why?

This is only for 1 sub right cuz i have 2 2ohm subs

You can do this with 2 subs then i can bridge them both at 4ohm

How does going from 2ohm to 4ohms sound?

That anyone at here can help me i have some issue that i dont know how to wiring my 2 speaker=4ohm(i want to become a 8ohm) and 1 subwoofer=8ohm…my amp can support 8ohm so how can it be

If i was to do this with two 2ohm dvc subs, would I get a 4ohm load?